DJI Notifications

Hovermap is using a different robot than the connected remote control

The RC and the Hovermap are connected to different, incompatible models.

Ensure the correct Hovermap is connected. If the problem persists, land and restart the mission.

Take off failed

DJI reported that take off has failed for an unknown reason.

Investigate using the DJI Pilot app.

DJI: Critical warnings present

DJI is reporting a critical issue which needs investigation.

Land as soon as possible. Investigate using the DJI Pilot app.

DJI configuration changes: Multiple flight modes disabled

The Multiple Flight Modes setting could not be enabled, or it is currently trying to update to being enabled but the changes have not been applied yet.

The Multiple Flight Modes setting needs to be enabled for safe flight control with Hovermap.

DJI configuration changes: Enabling Multiple flight modes failed

Attempting to enable the Multiple Flight Modes setting with DJI failed.

DJI configuration changes: Novice mode enabled

The Novice mode setting is reported as enabled.

The Novice mode setting needs to be disabled for safe flight control with Hovermap.

DJI configuration changes: Downward vision positioning enabled

The Downward vision positioning setting is reported as enabled.

The Downward vision positioning setting needs to be disabled for safe flight control with Hovermap.

DJI configuration changes: Precision landing enabled

The Precision landing setting is reported as enabled.

The Precision landing setting needs to be disabled for safe flight control with Hovermap.

DJI configuration changes: Changing collision avoidance state failed

Attempting to change the state of the Collision avoidance setting through DJI failed.

DJI configuration changes: Changing RTH obstacle avoidance state failed

Attempting to change the state of the RTH obstacle avoidance setting through DJI failed.

DJI configuration changes: Landing protection enabled

The Landing protection setting is reported as enabled.

The Landing protection setting needs to be disabled for safe flight control with Hovermap.

DJI configuration changes: Changing landing protection state failed

Attempting to change the state of the Precision Landing setting through DJI failed.

DJI configuration changes: Enabling Landing protection failed

Attempting to enable the Landing protection setting with DJI failed.

Battery overheating

DJI has reported that the batteries in the drone are too hot. Robot may shut down mid-air.

Land immediately.

DJI: App is not registered

The DJI SDK registration could not be completed, which means you are unable to connect to the DJI RC.

Connect to the internet and restart the application to continue.

DJI: Low GPS signal

GPS signal is poor, or satellite search produced an error.

Move the robot to an open area to use GPS.

DJI: Warnings present

DJI reported a warning which needs investigation.

Investigate using the DJI Pilot app.

DJI: Flight Status unknown

The DJI flight assistant could not be contacted on the DJI remote control.

Reconnect the robot or restart the app if this persists.

DJI configuration changes: Battery critical threshold different

The critical battery threshold reported by DJI is different to the expected values.

DJI configuration changes: Setting battery critical threshold failed

Attempting to set the new critical battery threshold with DJI failed.

DJI configuration changes: Battery critical warning different

The warning battery threshold reported by DJI is different to the expected values.

DJI configuration changes: Setting battery warning threshold failed

Attempting to set the new warning battery threshold with DJI failed.

DJI configuration changes: Smart RTH enabled

The Smart RTH setting is reported as being enabled by DJI.

The Smart RTH setting needs to be disabled for safe flight control with Hovermap.

DJI configuration changes: Disabling Smart RTH failed

Attempting to disable the Smart RTH setting through DJI failed.

Geofence could not be disabled

DJI has detected low GPS signal, reported after the drone has been armed or while airborne.

Connect the RC to the tablet.

DJI: Low GPS signal

GPS signal is poor, or satellite search produced an error.

Move the robot to an open area to use GPS.

Drone downward sensors need to be covered with stickers to resolve the current DJI error

DJI reported that its sensors have detected a problem. This is likely caused by the downward sensors being uncovered during takeoff.

Altitude limited airspace

DJI reported that there is a maximum altitude limit which must be observed in the current flight area. Pilots must not exceed the altitude limit without authorisation (e.g. from CASA).

Ensure you have the appropriate approval to fly above this limit from the local aviation regulatory body.

DJI Visual Positioning is active

DJI reported that the in-flight vision positioning system has been activated due to low GPS for navigation.

Use DJI Pilot app to switch off if required.

DJI configuration changes: Multiple flight mode settings unknown

The current Multiple Flight Modes setting could not be determined from DJI.

DJI configuration changes: Battery critical threshold unknown

The current critical battery threshold could not be provided by DJI.

DJI configuration changes: Battery warning threshold unknown

The current warning battery threshold could not be provided by DJI.

DJI configuration changes: Smart RTH status unknown

The current Smart RTH setting could not be provided by DJI.

DJI configuration changes: Novice mode setting unknown

The current Novice mode setting could not be provided by DJI.

DJI configuration changes: Disabling novice mode failed

Attempting to disable the Novice mode setting through DJI failed.

DJI configuration changes: Downward vision positioning status unknown

The current Downward vision positioning setting could not be provided by DJI.

DJI configuration changes: Changing downward vision positioning failed

Attempting to change the state of the Downward vision positioning setting through DJI failed.

DJI configuration changes: Changing vision assisted positioning state failed

Attempting to change the state of the Vision assisted positioning setting through DJI failed.

DJI configuration changes: Precision landing status unknown

The current Precision Landing setting could not be provided by DJI.

DJI configuration changes: Changing active obstacle avoidance state failed

Attempting to change the state of the Active obstacle avoidance setting through DJI failed.

DJI configuration changes: Changing upward collision avoidance state failed

Attempting to change the state of the Upwards collision avoidance setting through DJI failed.

DJI configuration changes: Changing RTH obstacle avoidance state failed

Attempting to change the state of the RTH obstacle avoidance setting through DJI failed.

DJI configuration changes: Changing horizontal vision obstacle avoidance failed

Attempting to change the state of the Horizontal vision obstacle avoidance setting through DJI failed.

DJI configuration changes: Landing protection status unknown

The current Precision Landing setting could not be provided by DJI.

DJI configuration changes: Changing advanced pilot assistance state failed

Attempting to change the state of the Advanced pilot assistance setting through DJI failed.

Battery high age or wear

DJI has reported that the drone’s batteries have a high level of age or wear.

Battery too cold

DJI has reported that the drone’s batteries are too cold.

Battery cell broken

DJI has reported that one of drone’s batteries has a broken cell.

Geofence enabled

The Geofence applied by DJI is active.

Use DJI Pilot to disable geofence.

Geofence disabled

The Geofence applied by DJI is not active.

Use DJI Pilot to enable geofence.