--- title: "Using Commander" slug: "using-commander" status: "update" updated: 2026-10-19T02:39:39Z published: 2026-10-19T02:39:39Z canonical: "knowledge.emesent.com/using-commander" --- > ## Documentation Index > Fetch the complete documentation index at: https://knowledge.emesent.com/articles/llms.txt > Use this file to discover all available pages before exploring further. # Using Commander [Emesent Commander](/v1/docs/commander) is the Android app that is the interface to Emesent scanners, on a tablet or a smartphone. Operators use Commander to configure the scanner, and to plan, run, and monitor missions. ## Connect and configure Install and set up Commander with [Commander Getting Started](/v1/docs/getting-to-know-commander), then connect it to [Hovermap](/v1/docs/connecting-to-hovermap) or [GX1](/v1/docs/connect-gx1-to-commander). The Options menu gives access to the app functions and settings. In the Options menu, [Scanner settings](/v1/docs/scanner-settings) sets the audio volume, RTK corrections, and camera anti-banding frequency. ## Plan the mission Plan the scan before going to site. Check the [Hovermap operating limitations](/v1/docs/informational-article), and see [Scenarios](/v1/docs/scenarios) for the recommended techniques in common environments, such as stopes, shafts, bridges, and buildings. ## Set up the mission On the landing page, select a Mapping, Pilot Assist, or Autonomous mission. The [mission workflow](/v1/docs/mission-workflow) then goes through the pre-mission checks, connectivity, pre-mission settings, and scan setup, so the system is correctly configured before data collection starts. > [!WARNING] > Keep the device unlocked during a mission. If the device locks, the app can go into sleep mode and the live point cloud can have gaps. Hovermap continues to capture data. ## Start the mission For a Pilot Assist or Autonomous mission, arm the drone and take off from Commander. In an Autonomous mission, Hovermap runs Explore and Waypoint tasks in sequence. To take control at any time, switch to Pilot Assist. At the end of the mission, use [Return to Home](/v1/docs/return-to-home), then land and disarm the drone. For the full procedure, see [How to perform a mission (Mapping and Autonomy)](/v1/docs/how-to-perform-a-mission-mapping-autonomy). ## Monitor the mission The main view shows the live point cloud, and the header bar shows the mission status and system indicators. Commander also shows the [RTK status](/v1/docs/monitoring-rtk-status) and, for DJI drones, the drone telemetry on a map. Other people can watch the mission on their own device in [Observer mode](/v1/docs/observer-mode). ## Finish and process the scan When the robot is on the ground and disarmed, select **Stop Scan**. Then [transfer the scan data](/v1/docs/data-transfer) and process it. Onboard processing takes about 80 seconds for a 15-minute mission, against about 20 minutes in Aura, but the point cloud has a lower resolution. To choose a method, see [Aura and Hovermap onboard processing comparison](/v1/docs/aura-and-hovermap-onboard-processing-comparison). ## Common tasks | Task | Article | | --- | --- | | Connect Commander to Hovermap | [Connecting to Hovermap](/v1/docs/connecting-to-hovermap) | | Change the scanner settings | [Scanner settings](/v1/docs/scanner-settings) | | Plan a mission | [Hovermap mission planning](/v1/docs/hovermap-mission-planning) | | Run a Mapping, Pilot Assist, or Autonomous mission | [How to perform a mission (Mapping and Autonomy)](/v1/docs/how-to-perform-a-mission-mapping-autonomy) | | Run a Mapping mission on a smartphone | [Perform a mapping mission on a smartphone](/v1/docs/operating-on-a-smartphone) | | Continue a mission after the app restarts | [Resume a mission in progress](/v1/docs/resume-a-mission-in-progress) | | Watch a mission on another device | [Observer mode](/v1/docs/observer-mode) | | Check RTK quality during a mission | [Monitor RTK status](/v1/docs/monitoring-rtk-status) | | See drone telemetry on a map (DJI only) | [Using the map widget and overlay view](/v1/docs/using-the-map-widget-dji-only-and-overlay-view) | | Change the viewport view during a scan | [Use the first-person and third-person views](/v1/docs/use-the-first-person-and-third-person-viewport-views-in-commander) | | Measure distances in a point cloud | [Using measure tools in Commander](/v1/docs/using-measure-tools-in-commander) | | Review mission data after a scan | [Mission review and reports](/v1/docs/mission-review-and-reports) | | Choose between Aura and onboard processing | [Aura and Hovermap onboard processing comparison](/v1/docs/aura-and-hovermap-onboard-processing-comparison) | | Download log files | [Download Commander log files](/v1/docs/download-commander-log-files) |