--- title: "Configure Trimble Receiver" slug: "configure-trimble-reciever" updated: 2026-08-24T05:26:55Z published: 2026-08-24T05:26:55Z canonical: "knowledge.emesent.com/configure-trimble-reciever" stale: true --- > ## Documentation Index > Fetch the complete documentation index at: https://knowledge.emesent.com/articles/llms.txt > Use this file to discover all available pages before exploring further. # Configure Trimble Receiver Configure a Trimble GNSS receiver through its web interface so it can supply position data to Hovermap for RTK scanning. Complete the [Trimble hardware setup](/v1/docs/02-trimble-setup) before starting. ## What you will need - Hovermap unit with a Vehicle RTK or Backpack RTK mount and a Trimble GNSS receiver, configured as described in [Vehicle RTK](/v1/docs/vehicle-rtk) or [Backpack RTK](/v1/docs/backpack-rtk) - Access to a web browser. - RTK base station (optional). > [!NOTE] > Configure the receiver through the Trimble web interface rather than the Trimble controllers, to avoid overriding the receiver's settings. ## Procedure ### Step 1: Connect to the Trimble receiver 1. Turn on the Trimble receiver, then connect to its Wi-Fi network. 2. In a web browser, enter 192.168.142.1 in the address bar to open the Trimble web interface. 3. Enter the login credentials on the **Login** page. > [!NOTE] > The default username is **admin** and the default password is **password**. ![Trimble web interface login page](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/02_trimble_setup-image-g85cdjfj.png) **Figure 1.** The Trimble web interface Login page. ### Step 2: Check the NMEA installation Confirm that the NMEA option is installed. 1. Go to **Receiver Status > Receiver Options** in the left panel. The **Options** panel appears on the right. 2. In the **Options** column, find **NMEA**. Confirm that an X appears next to it in the **Installed** column. ![Receiver Options page showing NMEA marked in the Installed column](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/02_trimble_setup-image-ljttw9xv.png) **Figure 2.** The Receiver Options page with NMEA installed. ### Step 3: Configure the NMEA settings Configure the NMEA output settings so the receiver can communicate with Hovermap. 1. Go to **I/O Configuration > Port Summary** in the left panel. On the right, click **Configure** for the port assigned to the RS-232 Port 1 connection. 2. Set **Input** to **None** and **Output** to **NMEA**. 3. Under **Serial Port Setup**, configure the settings in the table below. 4. In the **Input/Output** section, set the output rate for each message in the second table below. | Setting | Value | | --- | --- | | **Baud** | 115200 | | **Parity** | N | | **Flow** | Disabled | | Message | Rate | | --- | --- | | **GGA** | 5 Hz | | **GSA** | 5 Hz | | **GST** | 5 Hz | | **ZDA** | 5 Hz | | **GSV** | 1 Hz | ![NMEA message list with output rates configured in the Input/Output section](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/02_trimble_setup-image-hkbbbblv.png) **Figure 3.** The NMEA message output rates. Click **OK** to save the port configuration. ![I/O Configuration Port Summary page for the configured RS-232 port](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/02_trimble_setup-image-fkuun2pk.png) **Figure 4.** The Port Summary page for the configured RS-232 port. ### Step 4: Configure the tilt and antenna height > [!WARNING] > Hovermap cannot detect an incorrectly set antenna height, so ensure it is configured correctly. 1. Go to **Receiver Configuration > Antenna** in the left panel. 2. In the right panel, configure the following settings. | Setting | Value | | --- | --- | | **Antenna Measurement Method** | Antenna Phase Centre | | **Antenna Height** | 0.000 | ![Receiver Configuration Antenna page with measurement method and height fields](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/02_trimble_setup-image-zeg2h8q7.png) **Figure 5.** The Antenna configuration settings. #### Using tilt compensation If the antenna height is set to 0.000, tilt compensation does not apply. Even so, disable tilt compensation for best performance: go to **Receiver Configuration > INS**, clear the **INS Enable** option, then click **OK** to save. ![Receiver Configuration INS page with the INS Enable option](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/02_trimble_setup-image-7cqxqrv7.png) **Figure 6.** The INS page, where tilt compensation is disabled. #### Receiver motion profile If the Trimble receiver is mounted on a vehicle, set **Receiver Motion** to **Kinematic** or another appropriate model for best results. This setting is under **Receiver Configuration > Position**. Click **OK** to save. ![Receiver Configuration Position page with the Receiver Motion setting](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/02_trimble_setup-image-c2lppbh9.png) **Figure 7.** The Receiver Motion setting under Receiver Configuration > Position. ## Outcome The Trimble receiver is now configured for use with Hovermap and ready to capture RTK scan data.