--- title: "Attaching the Quick Mount" slug: "attach-gx1-to-quick-mount" updated: 2026-08-24T05:26:55Z published: 2026-08-24T05:26:55Z canonical: "knowledge.emesent.com/attach-gx1-to-quick-mount" stale: true --- > ## Documentation Index > Fetch the complete documentation index at: https://knowledge.emesent.com/articles/llms.txt > Use this file to discover all available pages before exploring further. # Attaching the Quick Mount This article explains how to attach the GX1 to the **Quick Mount**, the standard interface for connecting the GX1 to supported accessories (backpack, supported handheld, survey pole, or vehicle mount). Attach the **Quick Mount** to the accessory before attaching the GX1. The GX1 attaches in one of two orientations, depending on the accessory. ## Prerequisites - The GX1 - The GX1 **Quick Mount** - The accessory the GX1 is being mounted to (backpack, supported handheld, survey pole, or vehicle mount) ## Procedure ### Step 1: Attach the Quick Mount to the accessory 1. Attach the **Quick Mount** to the accessory before handling the GX1. For accessory-specific instructions, see the relevant setup article under Related articles. - [Mount GX1 on a Survey Pole](/v1/docs/mount-gx1-on-a-survey-pole) - [Set up GX1 Backpack Harness](/v1/docs/set-up-gx1-backpack) ### Step 2: Unlock the Quick Mount 1. Pull up the **Locking Lever** on the side of the **Quick Mount** until it is fully open, approximately 90° to the body. 2. Confirm the red indicator on the side is visible. This means the **Quick Mount** is unlocked and ready to accept the GX1. | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684155110.png) | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684226486.png) | | --- | --- | ### Step 3: Place the GX1 on the Quick Mount 1. Confirm the GX1 is powered down and not performing a scan. 2. Grasp the GX1 by the **Structural Support Struts**. 3. Place the GX1 onto the **Quick Mount**, aligning the **Locking Lever** with either the **Battery Bay Door** or the **Control Panel**, depending on the accessory orientation. | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684362400.png) | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684422213.png) | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684575409.png) | | --- | --- | --- | ### Step 4: Seat the GX1 1. Press down gently and confirm the GX1 seats fully, past the retention locks. A GX1 that is not fully seated will be ejected when the **Locking Lever** is closed. 2. Hold the GX1 firmly, as it is not yet locked in place. ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684697805.png) ### Step 5: Lock the Quick Mount 1. Press the **Locking Lever** down until it is flush with the body of the **Quick Mount**. Keep the GX1 supported until it locks. 2. Confirm the **Locking Lever** seats completely and the red indicator is no longer visible. | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684823811.png) | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684852619.png) | ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/image-1782684884837.png) | | --- | --- | --- | ### Step 6: Confirm the connection 1. Confirm a positive lock was felt and heard as the GX1 secured, then perform a firm pull test to confirm the GX1 is fully locked into the **Quick Mount**, with no movement between them. 2. If the GX1 is incorrectly oriented, the **Quick Mount** pushes it away to show it is not locked in. If this happens, re-check the alignment and seating, then try again. ![](https://cdn.document360.io/c908b593-57d7-4fc8-b409-592fc1051369/Images/Documentation/IMG20260626104502.jpg) ## Outcome The GX1 is securely attached to the **Quick Mount** and ready for use with the intended accessory.